xl2tpd-1.3.15p0

This README contains unresolved ports variables; replace them before using its commands.

+-----------------------------------------------------------------------
| Running xl2tpd on OpenBSD
+-----------------------------------------------------------------------

Note that this port is not fully operational. It is useful in some cases,
but in general for situations supported by npppd(8) from OpenBSD's base
system (for example LNS "server" use), it is strongly recommended to use
that option instead.

As of this time, npppd(8) does not support client-side operations (LAC),
so this port is useful there.

Basic operation
===============
xl2tpd makes a connection via L2TP, but uses pppd(8) to carry out most
operations; therefore most PPP-related configuration is done via pppd's
configuration files; for an example of how to configure this, see
${TRUEPREFIX}/share/examples/xl2tpd/ppp-options.xl2tpd.

You will also need to add the _xl2tpd user to the group 'network' in
/etc/group in order to allow it to start pppd.

Control mechanisms
==================
When xl2tpd is started, it does not automatically connect. Instead it is
controlled by writing simple commands to a fifo (you may be familiar with
this style from isakmpd), e.g.:

  echo '[command] [config_name]' > /var/run/xl2tpd/l2tp-control

Where [command] is one of:

  c    connect; may be followed by authname and password
  d    disconnect
  r    (disconnect and) remove

To connect, you must ensure that a free ppp(4) interface is available
("ifconfig ppp0 up" or "echo up > /etc/hostname.ppp0"), and then you must
send the 'c'onnect command to actually bring up a session; this does not
happen automatically.

An xl2tpd-control program is also available and you might be able to use
it as an alternative to the above, but it has some issues.

L2TP+IPsec
==========
To use an IPsec-protected tunnel, as you might want to do if connecting to
an npppd server, the IPsec tunnel must be configured separately using
isakmpd(8) - here are sample config sections (adjust $server, $ipsec_psk,
etc. as necessary, and you may need to adjust the auth/enc/group settings):

- /etc/ipsec.conf

ike dynamic esp transport proto udp from egress to $server port 1701 \
    main auth "hmac-sha" enc "aes" group modp2048 \
    quick auth "hmac-sha" enc "aes" \
    psk $ipsec_psk

- ${SYSCONFDIR}/xl2tpd/xl2tpd.conf:

[global]
debug avp = yes
debug network = yes
debug state = yes
debug tunnel = yes
port = 1701

[lac l2tp]
lns = $server
ppp debug = yes
pppoptfile = /etc/ppp/options.l2tp

- /etc/ppp/options.l2tp:

ipcp-accept-local
ipcp-accept-remote
noccp
noauth
mtu 1456
mru 1456
debug
lock
user $username
netmask 255.255.255.255

- /etc/ppp/chap-secrets:

$username	*	$password		*

Enable/start isakmpd:

# rcctl enable isakmpd
# rcctl set isakmpd flags -Kv
# rcctl start isakmpd
# ipsecctl -vf /etc/ipsec.conf

And confirm that the tunnel does actually come up:

# ipsecctl -sa
FLOWS:
flow esp in proto udp from $server port l2tp to $me peer $server \
srcid $myhostname dstid $server/32 type use
flow esp out proto udp from $me to $server port l2tp peer $server \
srcid $myhostname dstid $server/32 type require

SAD:
esp transport from $me to $server spi 0x1037c0f2 auth hmac-sha1 enc aes
esp transport from $server to $me spi 0x6c3d9e6a auth hmac-sha1 enc aes

If that is successful, you can try to make the L2TP connection:

# ifconfig ppp0 up
# rcctl start xl2tpd
# tail -f /var/log/daemon &
# echo c l2tp > /var/run/xl2tpd/l2tp-control

If all is well, you'll see debug output in the log, and the interface
should be connected:

# ifconfig ppp
ppp0: flags=28051<UP,POINTOPOINT,RUNNING,MULTICAST,NOINET6> mtu 1456
	priority: 0
	groups: ppp
	inet 172.28.15.223 --> 172.28.15.1 netmask 0xffffffff