WSMOUSED(8) - System Manager’s Manual #
WSMOUSED(8) - System Manager’s Manual
NAME #
wsmoused - wsmouse daemon
SYNOPSIS #
wsmoused [-2dfi] [-C thresh] [-D device] [-M N=M] [-p device] [-t type]
DESCRIPTION #
wsmoused listens for mouse events on the specified device and communicates them to the wscons(4) driver. Its purpose is to provide copy/paste functionality on the console. It does not happily coexist with the X Window System though, so it has to be killed before starting the X Window System.
By default, the left mouse button is used to select text
(in the familiar click-and-drag fashion);
the right button is used to extend the selection;
and the middle button pastes.
This behavior can be modified through the use of
-M,
e.g.
-M 2=3
maps the right mouse button to paste.
The options are as follows:
-2
Indicate that the mouse has two buttons. In that case, the right button pastes.
-C thresh
Set double click speed as the maximum interval in msec between button clicks. If omitted, the default value of 500 msec will be assumed. This option will have effect only on the cut and paste operations in the text mode console.
-D device
Use device as the display control device. If omitted, wsmoused will use the default value of /dev/ttyCcfg, which controls the wsdisplay0 display terminals.
-d
Enable debugging messages.
-f
Do not become a daemon and instead run as a foreground process. Useful for testing and debugging.
-i
Print the type and the protocol of the mouse and exit.
-M N=M
Assign the physical button M to the logical button N. You may specify as many instances of this option as you like. More than one physical button may be assigned to a logical button at the same time. In this case the logical button will be down, if either of the assigned physical buttons is held down. Do not put space around ‘
=’. Button numbers start from one, assigned to the leftmost button.
-p device
Use
*device*
to communicate with the mouse.
If this option is not present, the device opened is
*/dev/wsmouse*
(the multiplexer device that receives all mouse events from all wsmouse
compatible mice on the system).
For a serial mouse, you have to explicitly specify the serial port, i.e.
*device*
must be one of
*/dev/cua0[0-3]*.
-t type
This option only applies to serial mice.
It specifies the protocol used by the serial mice.
You may explicitly specify a type listed below or use
*auto*
to let
**wsmoused**
automatically select an appropriate protocol for the given mouse, if the
serial mouse respects the PnP COM specification.
If this option is not specified,
*auto*
is assumed.
Under normal circumstances, you need to use this option only if
the mouse is not PnP compatible.
Valid protocol types for this option are the following:
*microsoft*
Microsoft serial mouse protocol.
Most 2-button serial mice use this protocol.
*intellimouse*
> Microsoft IntelliMouse protocol.
> Genius NetMouse, ASCII Mie Mouse, Logitech MouseMan+, and FirstMouse+
> use this protocol as well.
> Other mice with a roller/wheel may be compatible with this protocol.
*mousesystems*
> MouseSystems 5-byte protocol.
> 3-button mice may use this protocol.
*mmseries*
> MM Series mouse protocol.
*logitech*
> Logitech mouse protocol.
> Note that this is for old Logitech models.
> *mouseman*
> or
> *intellimouse*
> should be specified for newer models.
*mouseman*
> Logitech MouseMan and TrackMan protocol.
> Some 3-button mice may be compatible with this protocol.
> Note that MouseMan+ and FirstMouse+ use
> *intellimouse*
> protocol rather than this one.
*glidepoint*
> ALPS GlidePoint protocol.
*thinkingmouse*
> Kensington ThinkingMouse protocol.
*mmhitab*
> Hitachi tablet protocol.
EXAMPLES #
To start wsmoused on the wsdisplay1 display terminals, using a two-button serial mouse connected to /dev/cua0:
# wsmoused -2 -D /dev/ttyDcfg -p /dev/cua0
To start wsmoused on the wsdisplay0 display terminals, using /dev/wsmouse with the left and right buttons swapped (assuming a three button mouse):
# wsmoused -M 1=3 -M 3=1
SEE ALSO #
HISTORY #
The wsmoused daemon is a slightly modified version of the moused daemon from the FreeBSD project, written by Michael Smith <msmith@FreeBSD.org>. Both inherit code from the XFree Project.
OpenBSD 7.5 - April 25, 2018